Connect Your Sleep Number® Smart Bed to Wi‑Fi

Applies to Sleep Number® 360, Sleep Number® Smart Beds, Climate™ and ComfortNext™ Collections.

Important: If your traditional (pre-2018) mattress was updated with a Firmness Control™ System after September 2026, the steps and information in this article apply to your bed.

View all supported mattresses

c2, c4, cSE, p5, p6, pSE, m7, iLE, i8, i10, hSE, Ultimate, ClimateCool®, Climate360®, ComfortNext™, ComfortNext™ Lux and ComfortNext™ Ultra

 

Quick Answer

Most customers complete setup in about 5-10 minutes.

To connect your Sleep Number® smart bed to Wi‑Fi:

  1. Download and sign in to the Sleep Number® app.
  2. Turn on Bluetooth on your mobile device and enable Bluetooth for the Sleep Number® app.
  3. Stay within 8 feet of your bed.
  4. Follow the in-app instructions.
  5. Select your home Wi‑Fi network and enter your password.

Once connected, you can access sleep tracking, software updates and other smart bed features.

 

Before You Start

Make sure:

✅ Your bed is fully assembled

✅ Your bed is plugged into power

✅ You have downloaded the Sleep Number® app

✅ You have a Sleep Number® smart bed compatible device

✅ Your smart bed is registered to your account

✅ Bluetooth is turned on in your device and enabled for the Sleep Number® app

✅ You know your Wi‑Fi network name and password

✅ You stay within 8 feet of the bed during setup

 

What would you like to do?

 

Why Get Your Bed Online?

Your bed is online when connected to both the Sleep Number® app and your home Wi-Fi network.

Benefits:

  • Sleep tracking
  • Responsive Air®
  • Software updates
  • Wellness insights
  • Support when you need it

 

Reconnect Your Bed After Changing Wi-Fi

If your bed was previously online and you recently:

  • Changed internet providers
  • Installed a new router
  • Renamed your network
  • Updated your Wi-Fi password

You'll need to update the Wi-Fi settings in the Sleep Number® app.

How to Update Wi-Fi Settings

Step 1: Open the Sleep Number App

Log in and select your bed.

Sleep Number app log in screen.
Step 2: Go to Smart Bed -> Settings -> check Bluetooth status

First make sure the Bluetooth icon is green.

If your icon is red or gray, follow the prompts in the Sleep Number® app to connect to your bed using Bluetooth. If you don't see any prompts, visit Trouble Getting Online for additional troubleshooting steps.
Sleep Number app showing Bluetooth disconnected status.
Sleep Number app showing Bluetooth and Wi‑Fi not connected.
Step 3: Select Connectivity -> Change WiFi

Choose Change WiFi and follow the prompts.

Step 4: Connect to Your New Network
  • Allow the App to scan for available wireless networks, this could take 1 – 2 minutes.
  • Select your Wi-Fi network and enter your password.
Sleep Number app screen that shows available wifi networks.

Once complete, your bed will connect to Wi-Fi and smart features will become available again.

 

Bed Offline: Replacement Pump

When you receive a new pump, you must go through the process of installing replacement electronics in the Sleep Number® app to get your bed back online.

How to get your bed back online after pump installation
  1. Turn Bluetooth on in your device settings. Stay within 8 feet of your bed.
  2. Tap Smart Bed. If you have multiple beds, make sure you select the correct bed.
  3. Tap the bed Settings icon in the top right corner.
  4. Select Install Replacement Electronics and follow the prompts within the app.
If your bed does not come online
  1. Perform a power cycle on your bed by unplugging your bed for 60 seconds. 
    • Smart Bed, Climate™ and ComfortNext™ Collections customers can go through the Sleep Number® app and choose Restart Bed.
  2. Plug your bed back in.
  3. After the bed fully reboots (takes 2-3 minutes), go to Settings and Support in the Sleep Number® app.
  4. Tap Install Replacement Electronics.

If you are having trouble getting online, find additional help with Trouble Getting Online.

 

If Your Network Doesn't Appear

  • Move the router closer to the bed.
  • Verify the router is connected to the internet.
  • Restart your router and bed.
  • Try connecting again.

 

If Your Password Isn't Accepted

  • Verify you selected the correct network.
  • Re-enter the password carefully.
  • Remember that passwords are case sensitive.
  • Retry setup.

 

Connect Your Bed for the First Time

Follow the steps below to connect your bed to the Sleep Number® app and your home Wi‑Fi network so you can access sleep tracking, software updates and other smart features.

The steps you see may look slightly different based on your bed model and app version. Follow the prompts in the Sleep Number® app for the most accurate instructions.

Step 1: Open the Sleep Number® app

Log into your Sleep Number account.

Sleep Number app log in screen.
Step 2: Start Setup by selecting Smart Bed → Finish Setup
An image of the Sleep Number app Finish Setup screen.
Step 3: Pair your Smart Bed

The app will guide you through pairing your bed using Bluetooth. Press and hold the pairing button, select Start Pairing in the app.

Depending on your setup:

  • FlexFit® Adjustable Base, Climate360® bases: Press and hold the Favorite button (located on the side of the frame, "at the hip") until the light flashes blue.
A zoomed in image of the favorite button being pushed and turning blue.
  • Mattress only, Integrated Base, Foundation and Adjustable Base with remote: Press and hold the Pair button on the pump until the light flashes yellow.
A zoomed in image of the Smart Control System (pump) with the pairing button called out.
Smart Control System
A zoomed in image of the firmness Control System (pump) with the pairing button called out.
Firmness Control System

Once bed and App are in pairing, the mobile device will prompt you to accept the Bluetooth connection.   Once accepted, the Bluetooth connection is successful.

Step 4: Connect to Wi-Fi
  • Allow the App to scan for available wireless networks, this could take 1 – 2 minutes.
  • Select your Wi-Fi network and enter your password.
The Sleep Number app choose wifi network screen.
Step 5: Complete Setup

Remain near your bed while setup finishes.

Sleep Number app confirmation screen indicating setup is complete.

For beds with a Smart Control System, you can run a quick system test to make sure everything is connected and ready for your first night of sleep.

Once complete, your bed will connect to Wi-Fi and smart features will become available.

 

Still having trouble getting online?

Visit Trouble Getting Online for additional troubleshooting steps. If you need further assistance, contact Sleep Number Customer Service.

 

Frequently Asked Questions

Why Does the Sleep Number® App Need Bluetooth?

The Sleep Number® app uses Bluetooth to connect your phone or tablet to the bed before sending Wi-Fi information to the bed. Once connected, your phone will remain connected through Bluetooth for additional adjustment functionality.

Where Is the Pairing Button on My Sleep Number® Bed?

The location of the pairing button depends on your bed configuration.

  • FlexFit® adjustable bases use the Favorite button located on the side of the bed near the hip area.
  • Beds without a FlexFit® adjustable base use the Pair button on the Smart Control System (pump).

During setup, the Sleep Number® app will guide you through the correct pairing process for your bed model.

Do I need the Sleep Number® app to get my bed online?

Yes. The Sleep Number® app is required to connect your smart bed to Wi-Fi and complete setup.

Does My Sleep Number® Bed Have to Be Online?

No. Your bed can still be used when it is offline.

You can continue adjusting your Sleep Number® setting and use supported adjustable base functions. However, connected features such as sleep tracking, software updates, and other smart features require the bed to be online.

Can I Use My Sleep Number® Bed Without Wi-Fi?

Yes. Your bed can still be adjusted without a Wi-Fi connection.

However, some connected features may not be available until the bed reconnects to the internet. Features that rely on connectivity, including sleep tracking and certain smart bed features, require the bed to be online.

What Happens If My Wi-Fi Goes Down?

If your home Wi-Fi is unavailable, your bed may appear offline in the Sleep Number® app.

Once your internet service is restored, your bed may reconnect automatically. If it does not reconnect, open the Sleep Number® app and verify your connectivity settings.

How Do I Know If My Sleep Number® Bed Is Online?

Open the Sleep Number® app and navigate to:

Smart Bed → Settings

A green dot next to the Wi-Fi symbol means your bed is connected. If your bed shows Offline, follow the troubleshooting steps in this article.

The Sleep Number app settings and support menu showing three green dots, next to online, the wifi and bluetooth signal
What features require my bed to be online?

Sleep tracking, enabling Responsive Air® technology, software updates, and other connected features require an online connection.

Can I still use my bed if it isn't online?

Yes. You can still adjust comfort settings, but connected smart features will not be available. 

I received my bed as an inheritance or through a second-hand purchase, how do I get it online?

If you received your bed from someone else or bought it secondhand, some connected features may not be available. Sleep Number® smart bed services and online features are not transferable to a new owner.

 

×
Was this article helpful?
5433 out of 17416 found this helpful
Please do not include any personal information in your feedback.